Click Here

 

Listed here in the next paragraph you can get a bunch of awesome ideas regarding How to Install a Bathtub.

Setting up a bath tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult job. If the old tub is easily accessible, the job can move easily; if you need to open up a wall to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and embeded in the brand-new one. Make sure you have actually certified yourself for the work and also fit attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you might need a professional plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your restroom if you have actually already gotten a brand-new bathtub and also do not require to change the plan of your previous supply of water pipes.
Your devices as well as material checklist must comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Preparing for the Installment

To start with, the supporting framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Bathtub

Using the two wood boards under its feet, position the bath tub in the called for setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the spirit level reads level.
To install taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water system and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Load the tub as well as likewise check the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub should wait till the tub has actually been utilized at least when as this will resolve it into its last setting.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the maker offered backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap ports. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bath tub

In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you enjoyed our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking a few minutes to read through our blog. So long as you appreciated our blog entry please remember to pass it around. Thank-you for taking the time to read it.

Book A Service